Thermal and mechanical stresses in a solar central receiver A. Montoya, M.R. Rodríguez-Sánchez, J. López-Puente and D. Santana   2018/04/20

Abstract

Failure in the tubes of the solar receiver is a problem that should be studied. This failure is caused by the combined action of the high temperature, stresses and corrosion.
Commonly, the calculation of the stresses in the receiver tubes is carried out in the crossed sections, taking into account the radial and the circumferential variation of the temperature. However, the temperature gradient along the tube length has been ignored.
In this study a new model for the stress calculation in the receiver tubes has been developed. This model includes the temperature gradient in circumferential, radial, and longitudinal direction, taking into account the movement restrictions.
The results show that the mechanical boundary conditions have a large effect in the stresses of the tube, being 3 times higher than the stress when no movement restrictions have been imposed.
Moreover, the stress profile is highly dependent on the temperature gradient and hence on the incident solar flux on the receiver. Homogeneous solar fluxes are then more suitable than lower levels of solar fluxes with important gradients.

Authors and affiliations

A. Montoya1a, M.R. Rodríguez-Sánchez2b, J. López-Puente1 and D. Santana2
1. Department of Structure and Continuous Media.
2. Department of Thermal and Fluid Engineering
Carlos III University of Madrid. Campus of Leganés, 28911 Madrid (Spain)

Key words

Solar power tower, solar receiver, thermal gradient, thermal stresses, FEM analysis.

References

[1] Gauche, P., Rudman, J., Mabaso, M., Landman, W. A., von Backstrom, T. W., Brent, A. C. System value and progress
of CSP. Solar Energy 2017, Vol. 152, pp. 106-139.
[2] Gertig, C., Delgado, A., Hidalgo, C., Ron, R. SoFiA a novel simulation tool for central receiver systems. Energy
Procedia 2014, Vol. 49, pp. 1361-1370.
[3] Marugán-Cruz, C., Flores, O., Santana, D., García-Villalba, M. Heat transfer and thermal stresses in a circular tube with a non-uniform heat flux. International Journal of Heat and Mass Transfer 2016, Vol. 96, pp. 256-266.
[4] Du, B.-C., He, Y.-L., Zheng, Z.-J., Cheng, Z.-D. Analysis of thermal stress and fatigue fracture for the solar tower
molten salt receiver. Applied Thermal Engineering 2016, Vol. 99, pp. 741-750.
[5] NREL. Concentrating Solar Power Projects, 2017. https://www.nrel.gov/csp/solarpaces/project_detail.cfm/proj ectID=40
[6] Special Metals Corporation. Incoloy alloy 800H & 800HT. SMC-047, 2004.
[7] Zavoico, A.B. Solar power tower: Design basis document. Sandia National Laboratories, San Francisco, SAND2001-
2100, pp. 1-148.
[8] Sánchez-González, A., Santana, D. Solar flux distribution on central receivers: a projection method from analytic
function. Renewable Energy 2015, Vol. 74, pp. 576-587.
[9] Sánchez-González, A., Rodríguez-Sánchez, M.R., Santana, D. Aiming factor to flatten the flux distribution on cylindrical receivers. Send for publication to Energy, 2018.
[10] Rodríguez-Sánchez, M.R., Soria-Verdugo, A., Almendros- Ibáñez, J. A., Acosta-Iborra, A., Santana, D. Thermal
design guidelines of solar power towers. Applied Thermal Engineering 2004, Vol. 63 (1), pp. 428-438.